MINI Bio Light Machine: BB-MN10

MINI Bio Light Machine: BB-MN10

 Operating Instructions

Safety Instructions: Please read the safety instructions before using this product. The safety instructions explained here are to help you use this product safely and in a correct manner so injuries to you and others can be avoided. The safety instructions shown here are classified as follows:

WARNING: Not following the below procedures could lead to the machine being damaged/malfunctioning, fire, and/or personal injury (ies).

1. Do not use the unit for other reasons than the intended purpose.
2. Do not use the product if you have damaged it by dropping or knocking it over.
3. Make sure plug and outlet are the same voltage. Do not use an extension cord to connect the adaptor to an electrical outlet.
4. Remove plug from outlet if machine is not in use. Always hold on to the plug while unplugging and never unplug by pulling the cord.
5. Do not cut, damage, or modify the cord. Do not pull or twist the cord with unnecessary force. Do not wind the cord around the product. If the cord is damaged or gets heated up, discontinue use immediately.
6. Do not use the unit near inflammable material such as Benzene, paint thinner, sprays, etc. Do not use thinner, benzene, or other solvents to clean the unit as it may damage the unit.
7. Do not use the product while your hands are wet. Handle it with dry hands only.
8. Do not place, store, or use product near place where it is exposed to water such as bathtubs, sink, or other vessels, and areas with high humidity. It may cause damage to the interior of the machine. Do not submerge the product in water.
9. Do not use the product when the temperature is below 0 degrees Celsius or above 40 degrees Celsius, or when exposed to direct sunlight, heat, or too much moisture.
10. Keep unit away from children. Do not let them play with the unit. Most importantly unit should never be use on children

 REPAIRING THE UNIT:

1. Do not attempt to repair, disassemble, or modify the unit on your own. You may injure yourself as a result of fire, or abnormal operation.
2. The supply cord of this appliance cannot be replaced. If the cord is damaged, the appliance should be discarded.

IDENTIFYING PARTS

1. Output of pure red light
2. Output of BIO electricity
3. Touch sensor (to keep the currency loop)
4. Display bulb of BIO electricity function
5. Display of currency power
6. Button of BIO electricity power control
7. Button of only BIO electricity working
8. Indication light of pure red light output
9. Working time for 15 minutes

10. Working time for 10 minutes
11. Working time for 5 minutes
12. “Start” button
13. Button of only pure red light working
14. ON/OFF switch
15. Button to select working time
16. Cooling fan window
17. Adaptor input
18. Adaptor

640NM PURE RED LIGHT TECHNICAL AND FUNCTION:

Wave length: 640nm pure red light, the simple, low powered wave is highly efficient when it comes to treating acne. This kind of pure red light can help the cells of the human body to remain in good condition by supplying them with energy.

BIO (TINY ELECTRICITY) FUNCTION:

The tiny electricity supply is similar to BIO currency. It can offer the energy to cells enabling them to diminish inflammation, as well helping to remove wrinkles.

INSTALLATION & HOW TO USE:

1. Connect the adaptor with the power supply
2. Connect the main unit with the adaptor.
3. Turn on the machine and stand by as the pure red light and BIO electricity is on “on” position.
4. Push the “Start” button, the BIO function can be used when output of pure red light is all bright, and the display bulb of BIO electricity function is glittering.

 Attention:

• Handle touch sensor of both side of the main unit, put output of BIO electricity on the face, and then adjust button of BIO electricity power control. It is normal that there is no feeling because of weak BIO electricity. Person will experience a weak feeling when machine is use around the mouth and eye.
• Use sensors of BIO electricity around acne to treat acne and use censor to treat skin.
• It is normal for the machine to become hot after working with it for several minutes.

1. If you want to use BIO function on yourself, push button so only the BIO electricity is working. The display bulb of BIO electricity functions remains on while the indication for the output of pure red light goes off. Turn on “Start” button to work.
2. If you want to us HI-FREQ function, push button for the output of pure red light for it to start working after seeing that the display bulb of BIO electricity function is off. Turn on “Start” button to work.

Ref. #: BB-MN10